The Millennium Master is a homebuilt aircraft that features a very sleek, modern-looking profile. The design offers notable cruising speeds, outstanding performance and excellent visibility from the large, 2-seat cockpit. You'll find that Flyzone's Millennium Master model captures all of the full-size plane's scale looks, from the flowing lines to the authentic trim scheme. It also replicates the kit's wide performance envelope and sport aerobatic capabilities. Final assembly is a breeze - so you can be out enjoying the Millennium Master's outstanding flight characteristics in no time.
This Rx-R version offers you the flexibility to install your choice of receiver and battery. The powerful brushless motor, ESC and micro servos are already installed, getting you in the air that much quicker!
• With its simple, straightforward assembly, the Millennium Master can be flight-ready in just minutes. • The large hatch attaches magnetically, and the battery compartment is roomy enough to accept a wide variety of battery packs. • Each aileron has a dedicated servo for positive control, as well as allowing mixing options for experienced pilots. • The tricycle landing gear and steerable nosewheel provide excellent ground handling.
The Huntsman, like its smaller brother the Smart-K, is an excellent introduction to flying as a basic trainer or even as a park-flyer for an experienced pilot. Unlike other similar models, this one includes ailerons, making it capable of mild aerobatics and therefore suitable for progression to a more manoeuvrable aircraft later on. The ingenious tail mounting system acts like an old freeflight dethermaliser by stalling the airframe allowing it to 'parachute' stall down to the floor (check out the video below). This combined with the rear-mounted prop makes the Huntsman very resilient to crash damage and thereby ensuring flying fun!
This new version includes an updates colour scheme
Joysway Dragonfly V2 ARTF - Fly from Land or Water
The popular Joysway Dragonfly has been upgraded to this stunning V2 variant. This 'All Terrain Launch and Land' model is capable of flying from almost any surface making it equally at home on water as it is on grass. The bright orange airframe is moulded from EPO foam to be both light and strong. It is easy to assemble and use with large access hatches (secured by strong magnets) for the flight battery and Rx.
The Dragonfly is as exciting to fly as it is versatile thanks to its powerful, rear mounted brushless motor with an over 1:1 power to weight ratio. Keeping the motor high up allows the propeller to be clear of water spray for maximum power on take off.
To top it off the Dragonfly is supplied pre-fitted with 4x 9g servos and a brushless ESC/Motor ready for use. Just add your choice of Tx/Rx combo and a 3S 11.1V 1300-2100mAh Li-Po battery to get in the air. Assembly takes less than 30 min!
• Versatile design allows use on land, sea, snow etc... • Powerful brushless motor and ESC included • Includes a balloon to keep your RX dry • Easy battery access • Spare propeller included
Included in the Box: • Dragonfly V2 Aircraft • 2 x Nylon propellers • Instruction Manual
Required to Complete: • 3S1P 1300-2100mAh 30C Battery and suitable charger • 4 Channel 2.4GHz Tx/Rx combo
The Bolero is a high performance funfly aircraft with huge control surfaces for 3D flight. The wings are fully symmetrical and feature a thick custom aerofoil to improve flight characteristics on windy days and a predictable response during slow speed. The fuselage is long to increase pitch stability and thin to help the Bolero track straight and true. The tailplane is open structure to reduce weight and the control surfaces themselves are huge and capable of large throws. The Bolero can be wild in the right hands but that shouldn't scare any novice aerobatic pilots away. Simply reduce the control movements down and the Bolero is docile enough to learn aerobatics and make a great first mid-wing model. The Bolero is predictable, smooth with the ability to progress with you as you become a 3D pro!
Brand New Scheme!
• All balsa and ply construction • Pre-covered in high quality heat shrink film • Suitable for electric or I/C power - (option pack required) • Large control surfaces for 3D flight • Aluminium undercarriage • Optional side force generators for amazing knife-edge performance • 2-Piece wing with carbon spar for easy transport • Large access hatch
Specification Wingspan:1500mm (59") Length:1510mm (59.5") Weight:2900g (6.4lbs) - I/C Weight:3080g (6.8lbs) - Electric Servos:4-5 Standard Size (Req.) Radio System: 4-5 Channel (Req.)
Ripmax Mini Bolero EP ARTF - Wooden FunFly 3D Parkflier
A-ARTF6740 2 in stock
The Mini Bolero is a scaled down version of the popular larger Bolero. This practical sized parkflier is fully built from balsa and ply then covered in iron-on film to produce and strong and durable electric 3D funfly. The low wing loading and large control surfaces allow the Mini Bolero to excel in 3D flight and fast agile manoeuvres. The recommended motor provides 1.5:1 power to weight ratio so hovering and long vertical manoeuvres are a breeze.
Designed in CAD, then produced on jigs with laser cut parts and then covered in high quality iron-on film the Mini Bolero oozes quality that the equivalent size foam model just cannot match. All areas of the design and construction have been studied and optimised for performance and durability. The wings are fully symmetrical and feature a thick custom aerofoil to improve flight characteristics on windy days and a predictable response during slow speed flight. The wings are easy to attach and remove through the large fuselage hatch, but it is small enough to fit in a car fully assembled. The tailplanes are an open structure to reduce weight and the control surfaces themselves are huge and capable of large throws for the ultimate response.
The Mini Bolero is supplied with no electronics allowing you to choose your favourite components. We recommend a 2217-1100Kv brushless motor (Quantum II 400 recommended) with a 30A ESC (Quantum 30A recommended) and a 3S 1300-1800mAh 30C Li-Po (High Energy 3S1P 1300mAh 30C or 3S1P 1800mAh 30C recommended). You will also need four 9 gram digital servos with about 2kg/cm of torque (New Power XLD-09HMB or Quartz P-QZ102 recommended). Then you can use your choice of 2.4GHz radio equipment with a minimum of 4 channels.
The Mini Bolero can be wild in the right hands but that shouldn't scare any novice aerobatic pilots away. Simply reduce the control movements down and the Mini Bolero is docile enough to learn aerobatics and it makes for a great first mid-wing model. The Mini Bolero is predictable, smooth and extremely capable with the ability to progress with you as you become a 3D pro!
• All balsa and ply construction • Pre-covered in high quality heat shrink film • Large control surfaces for 3D flight • 1.5:1 Power to weight ratio! • Large hatch for easy access • 2-Piece wing with carbon spar
Included in the Box: • Pre-Covered Balsa/Ply Airframe • Fibreglass Cowling • Carbon Spar • Aluminium Undercarriage • Comprehensive hardware pack • A4 colour manual • Painted Spinner
Required to Complete: • 2217-1100KV Brushless Outrunner • APC 10x5" EP • 30A Brushless ESC • 4x 9g Digital Servos • 4-5 Channel 2.4GHz Tx/Rx • 3S 1300-1800mAh 30C Li-Po • Various hand tools and glues
Specification Propeller:APC 10"x5" EP (Rec.) Type:Wooden ARTF Wingspan:950mm (37.5") Length:950mm (37.5") Weight:870-920g (31-32.5oz) Servos:4x 9g Micro Digital (Req.) Radio System:4-5 Channel 2.4GHz (Req.) LiPo:3S1P 11.1V 1300-1800mAh 30C (Rec.) Electric Motor:2217-1100Kv (Req.) Speed Controller:30A Brushless (Req.)
Ripmax Chris Foss WOT4 MK2 EP/GP ARTF
A-CF002/A 2 in stock
The ever popular WOT 4 ARTF has been given a makeover for 2016, the primary aim being to make it suitable for either I/C or electric power. Its strong, lightweight balsa and ply structure is supplied expertly factory built and finished in heatshrink film, so the WOT 4 Mk2 ARTF is flight ready in minimum time. The model comes complete with durable aluminium undercarriage, pre-painted fibreglass cowl and comprehensive accessory pack including wheels, linkages and more!
A large hatch with a spring loaded locking pin has been installed in front of the wing to allow access for flight battery changes. Alternatively it also makes access for fuel tank and receiver battery installation simpler. A ply battery mount/tray system is available, which makes battery changes quick and easy while ensuring that the battery is properly secured. To choose between EP or IC power you just need to purchase the relative optional hardware pack that suits your chosen power source.
In adition to structureal changes the model has been finished in a bright new color scheme in common with the latest Chris Foss designs. This bright and attractive new scheme aids with orientation and makes you model stand out at the flying field.
In the air is where the WOT 4 excels... it can be flown at little more than walking pace under full control and then push the throttle open and you're rewarded with a sparkling aerobatic performance. One word best describes the WOT 4. Versatile. With reduced throws it's the perfect follow on from a trainer. With the recommended throws it's the perfect sports model with loops, rolls, flicks and spins being well within its repertoire. Experienced pilots will want to increase the throws further and, when fitted with a powerful engine at the top end of the recommended range, the sky really is the limit! With terrific vertical performance this highly aerobatic model will satisfy the most demanding pilot.
Is there a better stunt model? We don't think so!
• Designed and Developed by Chris Foss • Highly Aerobatic - Sensational Performance & Amazing Low-Speed Manoeuvrability • Pre-formed aluminium undercarriage and pre-painted fibreglass cowl • Lightweight CNC balsa/ply construction • Factory covered in heatshrink film • Bold new colour scheme! • Suits either electric or I/C power (Pack sold seperately) • Suitable for a wide array of skill levels
Optional Power Packs I/C Hardware Pack: A-CF002/ICP Electric Hardware Pack: A-CF002/ELP
The saying 'Good things come in small packages' perfectly describes the Mini Wot4 ARTF. The Wot4 design is well established as one of the worlds favourite RC aircraft and this 670mm wingspan parkflier format it lives up to the reputation of the Chris Foss name. This lightweight parkflier is perfect for parks or small fields.
The Mini Wot4 is a beautifully wooden ARTF with an electronics package ready for you to start assembly. The electronics package includes a brushless motor, a brushless ESC and four micro servos. To complete you only need to add a suitable 650-800mAh 2S battery and micro receiver to finish the airframe off. The main structure is supplied pre-built from lightweight balsa/ply and covered in iron on film. The kit includes a durable moulded cowling and a comprehensive hardware pack that contains lightweight wheels, aluminium undercarriage, pushrods and horns, together with full colour step-by-step instructions.
• Brushless motor, ESC and 4 x micro servos included • A practical size to store fully assembled! • Wooden construction • Efficient brushless motor • Aluminium undercarriage • Easy access battery hatch • Perfect for small fields and parks
Kit Contents: • Factory built wooden airframe covered in iron-on film • Electronic package including a brushless motor, ESC & 4 micro servos • Pre-formed aluminium undercarriage • Comprehensive hardware package • Full colour, step-by-step assembly instructions
Required to Complete: • 4-5 Channel Transmitter and Receiver • 4 x 100mm extension leads • Cyano glue (and epoxy if preferred) • 2S1P 7.4V 650 - 800mAh (O-HE2S1P065030A Recommended) & suitable charger • JST connector for speed controller if using O-HE2S1P065030A (P-AK0256) • Various hand tools
Specification Propeller:5.5 x 4.5" (Inc.) Type:ARTF Wingspan:670mm (26.4“) Length:570mm (22.4") Weight:260-280g (9.2-9.9 oz.) Servos:4 x Micro (Inc.) Radio System:4-5 Channel (Req.) LiPo:2S1P 7.4V 650-800mAh (Req.) Electric Motor:1510 Brushless (Inc.) Speed Controller:10A Brushless (Inc.)
Chris Foss/Ripmax Wots Wot Foam-E ARTF
A-CF050 2 in stock
The Wots Wot Foam-E makes for a perfect all round sports foam aircraft. The Wots Wot Foam-E combines the slow speed characteristics of the Wot4 Foam-E and the precision and 'locked in feel' of the Acrowot Foam-E. The Wots Wot Foam-E has been specifically designed to suit a popular 3S 2200mAh Li-Po battery resulting in a model that will fit in a hatchback car boot fully assembled! For a little more flight time, try the Hi-Energy 2700mAh pack instead.
The power system consists of a higher power 920kv outrunner brushless motor with 40A brushless ESC that really packs a punch giving the airframe over 1:1 power to weight ratio! Using a popular 2200mAh battery the duration is approximately 8 minutes.
Supplied in RX ready format the four 9 gram micro servos, outrunner brushless motor and 40A ESC come pre-installed ready to connect up to your choice of receiver and li-Po battery.
Using the latest in foam moulding technology you will notice the edges are very crisp and sharp without the weight penalty of a denser foam. The control surfaces use 'live' style moulded foam hinges but they also have plastic hinges moulded into the foam for extra security.
Assembly is easy and requires only a cross head screwdriver. It's so quick it takes longer to fit the decals than to assemble the airframe!
In the air biplanes are associated with slow scale flight but not the WotsWot, thanks to four large ailerons the roll rate is fast and authoritive and the short moment of the design gives great elevator and rudder power. The Wots Wot really excels during slow speed flight and can be really docile with low rates on. Up the rates and open the throttle for flicks, spins and knife edge loops are more! The stall is benign and thanks to the biplane configuration it really slows down nicely for landing.
• Foam Hinge Line with Plastic Hinges Moulded-In • Crisp & Precise Foam Mouldings • Carbon Re-Inforced Internal Structure • Easy Wing Assembly • Removable Tail Wheel • Tough Aluminium Undercarriage • Large Colourful Decal Sheet
Specification Material:EPO Foam Propeller:ST 12 x 6 Electric (Inc.) Wingspan:1000mm (39.37") Length:945mm (37.2") Weight:1180g ( 2.6 lbs) Servos:4 x 9g Micro (Inc.) Radio System:4 Channel (Required) Connector:'T' Style Battery Connector Electric Motor:920kv Outrunner Brushless (Inc.) LiPo:3S 2200mAh Li-Po (Req.) Speed Controller:40A Brushless (Inc.)